Your local HVAC experts in Raymond, NH. From emergency repair to full system replacement, we handle every heating and cooling need.
Professional HVAC solutions for residential and commercial properties in your community.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
Properly sealed and insulated ductwork is essential for delivering rated BTU output to every room in your home. Our technicians repair collapsed sections, seal leaks with UL-listed mastic and mechanical fasteners, and verify balanced airflow across all supply registers after service.
A correctly sized heat pump installation eliminates the guesswork of mismatched equipment and undersized ductwork. Our technicians perform load calculations, verify airflow across the evaporator coil, and commission the system to manufacturer specifications for peak efficiency and longevity.
Whether you are purchasing a home, preparing for seasonal demands, or evaluating replacement options, a thorough HVAC inspection provides actionable data. Technicians measure airflow, test safety controls, assess AFUE and SEER performance, and deliver a written report with prioritized recommendations.
When your heat pump struggles to maintain temperature or runs continuously without reaching setpoint, the problem often traces to refrigerant leaks, failing capacitors, or degraded reversing valves. Skilled technicians restore rated HSPF and SEER performance through systematic component-level troubleshooting.
Upgrading to a smart thermostat enables precise scheduling, remote access, and energy usage reporting that can reduce heating and cooling costs by 10 to 15 percent. Professional installation ensures correct wiring to your HVAC system, including C-wire verification and multi-stage equipment compatibility.
Preventive furnace maintenance protects your household by identifying cracked heat exchangers, carbon monoxide risks, and failing ignition components before they cause a breakdown. Annual service preserves rated AFUE efficiency and ensures consistent airflow through cleaned blower assemblies.
Ductless mini-split systems deliver zoned comfort without invasive ductwork, making them ideal for additions, garages, and older homes. Professional installation includes refrigerant line routing, condensate management, and electrical circuit provisioning to achieve rated SEER performance up to 33 in top models.
Clean ductwork directly impacts the efficiency of your HVAC system by reducing static pressure and allowing unrestricted airflow to every register. Our technicians inspect for microbial growth, seal access points after service, and verify airflow improvements with anemometer readings post-cleaning.
Mini-split repair demands familiarity with variable-speed compressor technology and manufacturer-specific diagnostic protocols from Mitsubishi, Fujitsu, Daikin, and LG. Technicians trace electrical faults, recharge refrigerant to factory specifications, and replace condensate pumps to restore silent, efficient operation.
A complete HVAC installation addresses every component in the comfort chain, from the air handler and condensing unit to the thermostat and ductwork. Technicians ensure proper airflow, verify refrigerant charge, and test all safety controls before handoff to guarantee reliable, code-compliant operation.
Seasonal air conditioning maintenance prevents costly mid-summer failures by verifying refrigerant charge, cleaning condenser coils, and testing capacitor microfarad ratings against manufacturer tolerances. A thorough tune-up preserves SEER efficiency and extends compressor lifespan by reducing operational strain.
When your heating or cooling system fails unexpectedly, rapid diagnosis is critical to minimizing discomfort and preventing secondary damage like frozen pipes or heat-related illness. Emergency technicians isolate the fault, whether electrical, mechanical, or refrigerant-related, and execute repairs on the spot.
When your boiler produces inconsistent heat, unusual noises, or pressure fluctuations, the root cause often involves sediment buildup, failing motorized valves, or degraded seals within the hydronic loop. Experienced technicians restore system balance and verify safe operation through combustion analysis.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
KIC Refrigeration has proudly served communities like Raymond (pop. 11,096) since 2013, delivering HVAC solutions that combine NATE-certified expertise with high-efficiency equipment from top-tier manufacturers. Our technicians understand the specific heating and cooling demands that New Hampshire weather places on residential and commercial systems across the region, and they arrive prepared to handle them.
Every HVAC project in Raymond, NH starts with a comprehensive system evaluation — including static pressure testing and refrigerant analysis — and ends with a verified comfort check. We install equipment with SEER2 ratings up to 22 and AFUE ratings above 96 percent because the efficiency of the system matters just as much as the skill of the technician installing it.
The certifications, standards, and commitments that set our HVAC service apart.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
Our technicians live and work in the communities they serve. They understand local building codes, climate demands, utility rebate programs, and the HVAC challenges specific to your area. Local expertise backed by a nationwide service network means fast response and consistent quality everywhere.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
Most service calls are completed the same day you call. Our trucks are stocked with over 200 common parts — capacitors, contactors, ignitors, flame sensors, motors, and control boards — so we resolve the majority of repairs in a single visit without waiting on parts.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
Answers to the heating and cooling questions our customers ask most often.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most New Hampshire locations. For Raymond homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
Absolutely. Modern high-efficiency HVAC equipment can reduce heating and cooling costs by 20 to 40 percent compared to systems installed 15 or more years ago. The improvement comes from advances in compressor technology, variable-speed motors, and smarter controls. In Raymond, upgrading from a 10-SEER air conditioner to a 16-SEER2 or higher unit delivers substantial monthly savings — the higher the SEER2 rating, the less electricity consumed per BTU of cooling. On the heating side, replacing an 80-percent AFUE furnace with a 96-percent modulating furnace means that 16 cents of every heating dollar previously wasted up the flue now heats your home. Heat pumps offer even greater efficiency, delivering 2 to 4 times more heating energy than they consume in electricity. KIC Refrigeration calculates projected energy savings for any equipment upgrade so you can see the return on investment before making a decision.
HVAC repair costs in Raymond typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
The National Air Duct Cleaners Association recommends professional duct cleaning every 3 to 5 years for most Raymond homes. However, several factors can shorten that interval: households with pets that shed, family members with allergies or asthma, smokers in the home, and properties that have undergone recent renovation or construction work should consider cleaning every 2 to 3 years. Warning signs that your ducts need attention include visible dust or debris accumulating at register openings, musty or stale odors when the system runs, unexplained respiratory symptoms, and inconsistent airflow between rooms. Our NADCA-compliant cleaning process uses truck-mounted vacuum equipment and rotary brush agitation to remove dust, allergens, mold spores, and debris from your entire duct system. We also inspect for disconnected joints, damaged insulation, and air leaks that reduce system efficiency.
A comprehensive HVAC inspection from KIC Refrigeration in Raymond covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
Yes. The EPA estimates that Energy Star certified smart thermostats save Raymond homeowners an average of 8 percent on heating and cooling costs annually, which translates to $50 to $150 per year for a typical household. Models from Ecobee, Nest, and Honeywell Home use occupancy sensors, geofencing, and learning algorithms to build a schedule around your actual habits, automatically lowering temperatures when you leave and restoring comfort before you return. Many smart thermostats also provide energy usage reports, filter change reminders, and maintenance alerts that help you keep your system running efficiently. Some New Hampshire utility providers offer rebates of $50 to $100 on qualifying smart thermostat purchases, further reducing the cost. KIC Refrigeration installs and configures smart thermostats to communicate properly with your specific HVAC system — including multi-stage equipment and heat pumps that require specialized wiring.
Hear what our customers have to say about the quality and reliability of our HVAC work.
"Our mini split stopped cooling mid-summer and they fit us in the next morning. Diagnosed a bad capacitor, replaced it on the spot. Back to normal in under an hour."
"AC repair was fast and fairly priced. The compressor was failing and they had the part on the truck. Done in about ninety minutes."
"Good experience with the furnace tune-up. Technician was thorough and pointed out a couple things to watch for. Only reason for four stars is scheduling took a few days."
Our NATE-certified crews provide HVAC service throughout the surrounding area.